Power delivery networks have become a real performance limit for data center chips. A 600W AI GPU running near 0.7 V pulls about 1,000 amps, and at that level resistive losses and voltage droop eat into both speed and efficiency.
Designers are answering by moving the voltage regulators from the board edge to right beside, or even inside, the processor package.
Why current is the problem
Low supply voltages of 0.7 to 0.9 V mean multiple kiloamps are needed for modern GPUs. Multi-chiplet designs raise current density further and crowd signal routing. Fast workload swings make voltage droop worse, so designers add voltage margin, which burns more power and cuts efficiency.
A Synopsys product manager notes that even milliohm-level resistance can cause significant IR drop at these currents, which affects maximum frequency and minimum operating voltage. An Intel Foundry illustration shows the scale: moving from a 1kW to a 5kW GPU with board-level regulators, voltage regulator losses hold near 13%, resistive losses jump from 8% to 31%, and droop rises from 17% to 31%.
The pressure is also about energy use more broadly. TSMC’s Lipen Yuan told a 2024 IEDM short course that energy efficiency becomes the most important performance index for AI platforms. ASE’s CP Hung says the final stage of voltage regulation, closest to the chip, grows more important as board-to-chip demands rise. Multi-die designs bring power integrity to the forefront alongside thermal, stress and warpage issues, though the underlying problem already existed in advanced single-die chips.

Vertical power delivery
The industry trend is vertical delivery, with regulators placed:
- Under the PCB, directly below the processor.
- Inside the accelerator package, below the SoC, which is called integrated power delivery.
- Inside the silicon interposer, called fully integrated power delivery.
The idea began nearly a decade ago with backside power delivery on the wafer, which feeds transistors more directly and reduces IR drop. Synopsys’s Sojan Philips cautions that it doesn’t remove power-integrity problems. It also changes thermal behavior, since heat has more complicated paths out of the stack.

800V in the data center
Next-generation facilities are moving from traditional AC distribution toward 800V DC. Power would step down in stages, for instance to 48V, 12V and then 0.7V, with regulators near each load. Fewer conversions raise system efficiency and ease cooling.
proteanTecs’ Nir Sever says distributed integrated voltage regulators placed close to the chip reduce IR drop and shorten reaction to droop events from milliseconds to microseconds. That allows finer voltage tuning across different areas of a chip.

Who is building it
Suppliers are offering suites of options. ASE has PowerSiP packaging for PCB-backside integration, and says shortening the high-current path can cut parasitic routing losses by 50% or more. Marvell introduced its Package Integrated Voltage Regulator in June 2025, replacing discrete regulator parts that sit inches away with compact converters tied to the processor. Partners include Infineon, Ferric, Monolithic Power Systems and a compact-converter specialist.
Consolidation followed. Analog Devices closed its purchase of a compact-converter maker in July. On Nov. 2, onsemi announced it will acquire Ferric’s assets for up to $775 million.
An integrated voltage regulator is typically a 3D stack of deep-trench capacitor, power management IC and inductor, built into the substrate or interposer. The tradeoff, a Synopsys architect says, is new thermal and stress effects and noise coupling into neighboring dies. Intel Foundry says its Super High Density MIM capacitors can raise capacitance density 10x over conventional ones.
Packaging firms join the design loop
Because power delivery now crosses die, package and board, outsourced assembly and test firms are pulled into co-design earlier. Amkor’s Alex Kizeev says the best results come when the power budget is split across die, package and board, with foundries and fabless teams owning on-die power, substrate makers defining stackups, and packaging firms handling vias, capacitors, warpage and validation.
What happens next
The direction is closer integration of inductors, capacitors and conversion into substrates and interposers. Each step needs joint design of the chip, package and power parts, and each adds thermal work. As compute per package keeps rising, power delivery networks will decide how much of a chip’s silicon can actually be used.
Source: Semiconductor Engineering